stunnel-users

stunnel-users@stunnel.org

5 participants
3294 discussions

stunnel service problems...
by Jeremy Paje 10 Jun '08

10 Jun '08

Has anyone had any problems with the windows stunnel service not starting automatically? We install stunnel as a service (stunnel.exe -install) We've had it previously installed on 600+ machines with no problems, but recently (noticed on slower machines running XP) the stunnel service does not start...but it happens randomly only on slower machines. The following errors are in the event log... Timeout (30000 milliseconds) waiting for the stunnel service to connect. (Event ID ID 7009) AND The stunnel service failed to start due to the following error: The service did not respond to the start or control request in a timely fashion. (Event ID 7000) I've tried setting the service to restart if failed, and to delay 2 minutes before restart, etc with no luck. If you start the stunnel manually all is well, it just doesn't start on bootup. Any suggestions? Thanks JP

1 0

Re: [stunnel-users] stunnel compatibility question
by Brian Hatch 09 Jun '08

09 Jun '08

Roughly around 2008-06-09 11:34 -0400, Patel Dippen-CDP054 kibitzed: > In this scenario, can Stunnel listen on the UDP port on the local No. Stunnel will not listen on UDP ports. Stunnel will not send UDP packets. Stunnel doesn't support UDP. -- Brian Hatch The problem is that you'd Systems and probably make something Security Engineer useful of my life that http://www.ifokr.org/bri/ I would never do. Every message PGP signed

2 1

Fw: Re: stunnel compatibility question
by Jeffrey Buck 06 Jun '08

06 Jun '08

1 0

Re: [stunnel-users] stunnel compatibility question
by Brian Hatch 05 Jun '08

05 Jun '08

At almost 2008-06-05 09:37 -0400, Patel Dippen-CDP054 cajoled: > I guess what I am stating is can Stunnel listen on a UDP port The answer to that question is 'no, it cannot.' -- Brian Hatch "I was looking at bringing Systems and up some new servers on Security Engineer imaginary hardware." http://www.ifokr.org/bri/ --Jason Every message PGP signed

1 0

stunnel compatibility question
by Jeffrey Buck 04 Jun '08

04 Jun '08

2 4

Re: [stunnel-users] stunnel compatibility question
by Brian Hatch 03 Jun '08

03 Jun '08

In the neigborhood of 2008-06-03 07:58 -0400, Patel Dippen-CDP054 argued: > Will Stunnel work for UDP data? Stunnel only accepts TCP connections. > We have traffic going into the Server on UDP and outbound from the Server on TCP. You'll want an actual VPN protocol to handle that then. Or consider using a better protocol - what you describe makes the firewalls cry. > My understanding is that OpenSSL implemented the DTLS protocol (TFC > 4347: to support UDP data) in version 0.9.8 (OpenSSL: a free and popular > implementation of TLS added support for DTLS with version 0.9.8.) Not supported in Stunnel currently. -- Brian Hatch Always yield to temptation, Systems and because it may not pass Security Engineer your way again. http://www.ifokr.org/bri/ Every message PGP signed

1 0

Is anyone using Stunnel for tunnelling Voip?
by Errol Samuels 03 Jun '08

03 Jun '08

Hello All, I am currently researching a solution for tunnelling VoIP traffic since VoIP is blocked in the country concerned. It appears that the ISP is targeting OpenVPN and OpenSwan and blocking them so I want to try something different. My solution based on OpenVPN worked great until it got blocked by the ISP about a week ago. It was using an OpenVPN server hosted in a US Datacenter and the VPN clients were simply routers with third party Linux firmware with the OpenVPN client embedded in the firmware. I am also investigating the possibility of tunnelling OpenVPN through SSH but I have to watch my IP overheads here because the ISP watches the upload bandwidth as well! Has anyone attempted or had any success using stunnel for a similar scenario as I have mentioned? Thanks in Advance Regards, Errol

3 9

Can I put an accept+connect pair anywhere in the conf file?
by Ben Stover 02 Jun '08

02 Jun '08

The *.conf file is divided into several sections: [imaps] .... [pop3s] .... [smtps] ..... Are these "section headers" just comments and can I put my accept+connect pair on an arbitrary place in the *.conf file (as long as they are preceeded by their own section header [foobar] ? Ben

2 1

Connecting to mySQL from Windows
by Alistair Scott 02 Jun '08

02 Jun '08

Hi everyone I have a mySQL database that I need to connect to through SSH. I have successfully setup a connection to it using Plink. However, I'm running this from a batch file and I'd like a more elegant solution - that's where stunnel comes in I think. Rather than running a batch file, I'd like to run the connection as a Windows service - which I think this is achievable with stunnel. Trouble is, I can't work out how to do it. This is what I'm trying to achieve... Windows computer connects to mySQL server through SSH. Forwards a port to the mySQL server port 3306. Application on Windows computer connects to local forwarded port & therefore connects to the mySQL db at the remote end. I was hoping that someone could give me a pointer as to how I can set this up. Thanks in advance. Al

1 0

stunnel 4.25 released
by Michal Trojnara 01 Jun '08

01 Jun '08

Dear Users, Version 4.25, 2008.06.01, urgency: MEDIUM: * New features - Win32 DLLs for OpenSSL 0.9.8h. * Bugfixes - Spawning libwrap processes delayed until privileges are dropped. - Compilation fix for systems without struct msghdr.msg_control. Home page/download: http://stunnel.mirt.net/ sha1sum for stunnel-4.24.tar.gz file: fc6d61fad996f750c76ea627c5dd9f789af0eaf6 Best regards, Mike

1 0

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

stunnel-users