Hi all,
I am a new guy to stunnel.
here is the issue I meet, i install my stunnel in the lab. and trying to run the test with netcat.
Here is the config file i test:
client side: ... ... output = stunnel.log client = yes [ncat] accept = 12035 connect = ***.***.***.***:1230 then I run "stunnel test.conf "and the the log file shows configuration successfully
then I run the command "cat test.file | netcat ***.***.***.*** 12035 on the client side and run netcat -l -p 1230 > output nothing happens. And I check the log file. there is no record about the netcat. I don't know what happened.
Dewen;
I don't know anything about Netcat, so I'm taking a stab in the dark here, but it looks as if you're pointing Netcat at port 1230, while your config file indicates that Stunnel would be listening on port 12035. Try redirecting Netcat to the listening port.
If you need to post again, please indicate the version of Stunnel you are using, and what platform your are running it on.
Regards;
Thomas
On 3/16/2012 5:35 PM, Dewen Kong wrote:
Hi all, I am a new guy to stunnel. here is the issue I meet, i install my stunnel in the lab. and trying to run the test with netcat. Here is the config file i test: client side: ... ... output = stunnel.log client = yes [ncat] accept = 12035 connect = ***.***.***.***:1230 then I run "stunnel test.conf "and the the log file shows configuration successfully then I run the command "cat test.file | netcat ***.***.***.*** 12035 on the client side and run netcat -l -p 1230 > output nothing happens. And I check the log file. there is no record about the netcat. I don't know what happened.
-- */Dewen Kong/*
stunnel-users mailing list stunnel-users@stunnel.org http://stunnel.mirt.net/mailman/listinfo/stunnel-users
Dewen;
I think I misread your post. Please forgive me, as I'm unfamiliar with the Netcat application.
If you could provide some additional detail, that might be helpful.
Regards;
Thomas
On 3/16/2012 9:38 PM, Thomas Eifert wrote:
Dewen;
I don't know anything about Netcat, so I'm taking a stab in the dark here, but it looks as if you're pointing Netcat at port 1230, while your config file indicates that Stunnel would be listening on port 12035. Try redirecting Netcat to the listening port.
If you need to post again, please indicate the version of Stunnel you are using, and what platform your are running it on.
Regards;
Thomas
On 3/16/2012 5:35 PM, Dewen Kong wrote:
Hi all, I am a new guy to stunnel. here is the issue I meet, i install my stunnel in the lab. and trying to run the test with netcat. Here is the config file i test: client side: ... ... output = stunnel.log client = yes [ncat] accept = 12035 connect = ***.***.***.***:1230 then I run "stunnel test.conf "and the the log file shows configuration successfully then I run the command "cat test.file | netcat ***.***.***.*** 12035 on the client side and run netcat -l -p 1230 > output nothing happens. And I check the log file. there is no record about the netcat. I don't know what happened.
-- */Dewen Kong/*
stunnel-users mailing list stunnel-users@stunnel.org http://stunnel.mirt.net/mailman/listinfo/stunnel-users
-- Attention: This message and all attachments are private and may contain information that is confidential and privileged. If you received this message in error, please notify the sender by reply email and delete the message immediately.
stunnel-users mailing list stunnel-users@stunnel.org http://stunnel.mirt.net/mailman/listinfo/stunnel-users
-
Dewen Kong -
Thomas Eifert